One leg down, one to go!

It was quite a struggle and it took a few hours with the help of François.
Here is what was at stake:
 Fitting the right landing gear into this tight space

 Here it is done but aligning the bolts at the top of the picture with the holes is very awkward due to the lack of space to move the clamp and the lack of visibility. Two people have to be involved, one lying under the plane to move the clamp with the bolts and one looking from the top to guide the bolts into the holes.

This is the end result of the struggle: one gear leg in place, ready to receive its wheel.

One of the most difficult tasks since I started building. I felt lucky to be able to complete it without having to remove the rivets heads that were in the way as some builders did. Definitely not a one man job, thank you François for the help!
Let's wait until next year to take care of the left gear!
(Plus I have to visit my daughters during the holiday, one in New York and one in Washington DC, this will be a good break and well deserved too)

Wheeling and Dealing

This is what I discovered while mounting the tire on my front wheel:

This spot is diametrically opposed to the one above:
 

I have two more tires to mount but on inspection they do not seem to have this problem.
I have referred this to VANs and am waiting for their answer which hopefully will be a return.

As of December 17:
Vans sent me a new tire that I received today, no cost involved. They also asked me to return the bad tire to the tire vendor which I did. Issue closed.

What an RV-12 wheel is made of:

And don't imagine that it's easy to get there: the wheel comes all assembled and you have to pick it apart to mount the tire! Interestingly, there is no instruction to disassemble, in doubt I had to call Vans to make sure I was doing it right. Oh well, may be I'm not that smart!


At least I will know what keeps me rolling!

RV-12 going places

A fellow UK builder from Scotland (see his builder's log: http://www.mykitlog.com/grmps) shot these videos while flying over France and Italy:
(The camera is a wide angle positioned on the VS)
http://www.youtube.com/watch?v=ofOC-qKF1DU
http://youtu.be/_FYv045auC4
http://youtu.be/0NFhc__pzKY
Now, this is traveling light but in style!

Open Shop for EAA 1114

I put the wings on for the second time to show my RV-12 to my fellow EAA Chapter 1114 members. I enjoyed exercising some "bragging rights" after one and a half year of building (although I also learned to eat lots of humble pie during this period). We were fortunate to have a wonderful weather for December and I got all the help I needed to move my stuff around. I think that this initiative to open builder's workshop for our chapter's members is a great motivator both for builders and for members who wish to start building one day. One reason among many others that chapter 1114 is among the most dynamic EAA chapters in the country.

This thing has got wings! ...

... It must be a plane - So were the neighbors thinking today while driving by my workshop.

After working on a few contraptions allowing to move fuselage and wings around and having a runway built in front of my workshop, today the conditions were perfect to have a wing fitting session. I got help from my friend François Hautin (a former colleague from Alcatel and NC State) which allowed me to communicate in French, a language in which we are both better at cursing than English.

 One wing inside, one wing outside: this will allow me to carry on the building at home for a few more months. There is nothing like a 30 seconds commute to work!

François is recovering from the stress of carrying the two wings from my basement to my "Taxiway" which requires slaloming between the trees of my backyard:

 No damage done and the wings in place =  A happy builder!

 

Sequel to LSA America's visit

On our way back from Littleton, we stopped at Chuck Borsuk's workshop where Terry was to perform an inspection per his accredited EAA technical counselor function. Chuck is building a Pietenpol, a classic wooden plane and we were not disappointed by his workshop which feels more like a cabinet maker's than a plane builder's. Most impressing was the organization and tidiness of a shop whose tools and machines, beside Pietenpol parts are mostly producing sawdust and wood shavings. Not being qualified to comment on the work done so far, I let you make your own mind by looking at the following pictures. Needless to say, Chuck passed his inspection without reserve.

I have to say that there are rumors that the parrot bribed Terry's into giving Chuck a good grade... One might argue that a bird should be a good source of advice for a Tech Counselor but this one has clipped wings!

A visit to LSA America inc.

LSA America is the one of the few manufacturers of certified LSAs made in the USA. What is even more exciting for our EAA Chapter 1114 based in Apex, NC is that they are located in Littleton, NC just one and a half hour drive from the Research Triangle area. As the owners of LSA America, Doug and Betty Helmpstead are also the owners of my flight school, B-Bar-D aviation located at Sanford/KTTA. I had the privilege of a private visit to their manufacturing plant which opened in May of 2011. Accompanying me were fellow chapter members Chuck Borsuk, Terry Gardner and Niels Nielsen.
The current facility is located in the former " Littleton Industrial Building", an 54,000 square feet facility with plenty of room to spare:

The plans are to establish permanent production operations at the Halifax-Northampton Regional Airport. LSA America will create 34 new jobs and invest $400,000 during the next three years.
The State of North Carolina is helping LSA America through the "One NC Fund", other partners that helped with this project include: the N.C. Department of Commerce, N.C. Community Colleges, the Small Business and Technology Development Center (SBTDC), the N.C. Rural Center, the Halifax County Economic Development Commission, Halifax County Business Horizons, Halifax County, the Town of Littleton, the Halifax-Northampton Regional Airport Authority and North Carolina's Northeast Commission.

The Allegro:
  Specifications:
                                    MTOW: 1,320 lbs
                                    Empty Weight: 622 lbs (average)
                                    Max Useful Load: 698 lbs
                                    Fuel Capacity: 17 U.S. Gal (102 lbs)
                                    Payload: 596 lbs
                                    Range: 500 miles

The Allegro LSA is available with either the 80 HP  Rotax 912UL  or the 100 HP Rotax 912ULS.

Optional Equipment: Floats, Skis, Banner and Glider Tow Kits

There are about 500 Allegros flying oversees (with 57 registered in the USA per the FAA registry as of September 2011), all but one have been manufactured in the Czech  Republic.

So far one Made in USA Allegro has been produced and delivered by LSA America. It is currently used by a flight school in Michigan.

Made in USA Allegro #2 close to completion:

The wings of #2:

Note about the Allegro's wings: they are double-tapered which is unusual in LSAs and explains, according to Doug, the superior performances of the Allegro. This feature is more visible on the following picture:

Made in USA Allegro #3 already started:

Currently when a plane is ready it is trucked to the Halifax-Northampton Regional Airport for its flight tests. This step will not be necessary when the permanent production facility opens there in about a year.
We visited a few manufacturing station:

Wing Jigs:

Composite Lab where a cockpit dashboard is curing:

Doug Hempstead is explaining, part in hands, his strategy of switching parts manufacturing from outside contractors to in-house to better control quality and availability of components:

Some prototypes in early R&D stage: the Vampire pushers (the double seater is the object of a study by NC State's Aeronautic Department to decrease the weight of its composite hull)

What's next?
Doug Hempstead has the objective to build one Allegro a week. When will he get there depends on a number of factors some he controls some he does not. For example he mentioned the difficulties he is facing with immigration laws. Currently the manufacturing expertise on the factory floor comes from former employees of the former Czech company that used to produce the Allegro. Doug is facing great difficulties getting appropriate visas for these specialists whose involvement is critical to restarting the manufacturing as well as training new employees. By lack of an adequate visa these employees have to be sent back to the Czech republic every few months which is very disrupting and costly. Despite all the difficulties he is facing in this starting phase Doug is optimist and confident in the value of his product that he dares everyone to compare!
See more at http://www.allegrolsa.com/dare_to_compare
For those members of our EAA Chapter 1114, if you are interested in flying an Allegro, visit B-Bar-D  Aviation at Sanford airport, they offer discovery flight and if you are a pilot you can rent an Allegro at a very attractive rate. You also can take flight lessons as B-Bar-D is a well appointed Flight School (Trust me, I learned to fly and got my Sport Pilot Certificate there!)